Bonjour

Je suis sous linux Mepis (debian), j'ai installé Skype et il me reste un problème de son à résoudre.

Quand je fais le test de son avec echo123, le son retourné et très grave et lent. On dirait qu'il est au ralenti. J'ai essayé plein de choses mais je n'y arrive pas.
Quand je fais un enregistrement avec Audacity le son restitué est correct.

Voila .......
Si quelqu'un peut m'aider

merci

Bonjour

Peux tu m'en dire plus sur quelle machine est installé ta debian. Est-ce un micro incorporé etc .

Ce serait bien de mettre à jour ton profil.

@++

Bonjour et merci

Je ne sais pas si mon précédent message est parti (je ne le vois pas dans ce forum), dans le doute j'en envoie un autre.

J'ai mis à jour mon profil.
J'utilise un casque avec micro intégré Elypse
Détails de ma configuration:
Portable Acer TravelMate 2200
1256 de ram
Linux Distribution MEPIS (debian)
ADSL orange avec livebox
debit 8 mega
liaison ethenet eth0
Parefeu: Guardog
Version Sype (beta: version 2.1.0.81)
Pas d'antivirus

à bientôt

Bonjour

Peux-tu me faire une capture d'écran de ceci.

Tu lance dans un terminal :

Citation :

Bien sur avec ton micro allumé et Skype en route , avant de prendre la capture tu fais aussi un essai micro dans Skype.

J'attends tes résultats pour voir.

Bonne journée

@++

Bonjour
voilà la copie d'écran
root@mepis1:/home/mcd# dmesg
Initializing cgroup subsys cpu
Linux version 2.6.27-1-mepis-smp (MEPIS 2.6.27-43mepis1) (dev@mepis.org) (gcc ve
rsion 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP PREEMPT Fri Jan 8 13
:33:17 EST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005bf70000 (usable)
BIOS-e820: 000000005bf70000 - 000000005bf7b000 (ACPI data)
BIOS-e820: 000000005bf7b000 - 000000005bf80000 (ACPI NVS)
BIOS-e820: 000000005bf80000 - 000000005c000000 (reserved)
BIOS-e820: 000000006bf80000 - 000000006c000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
last_pfn = 0x5bf70 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 38000000 @ 10000-15000
RAMDISK: 3768e000 - 37fef545
ACPI: RSDP 000F69B0, 0014 (r0 PTLTD )
ACPI: RSDT 5BF77458, 0034 (r1 PTLTD RSDT 6040000 LTP 0)
ACPI: FACP 5BF7AF32, 0074 (r1 COMPAL ELW80 6040000 ATI 3)
ACPI: DSDT 5BF7789C, 3696 (r1 COMPAL ELW80 6040000 MSFT 100000E)
ACPI: FACS 5BF7FFC0, 0040
ACPI: APIC 5BF7AFA6, 005A (r1 PTLTD APIC 6040000 LTP 0)
ACPI: SSDT 5BF77687, 0215 (r1 PmRef Cpu0Cst 3001 INTL 20030224)
ACPI: SSDT 5BF7748C, 01FB (r1 PmRef CpuPm 3000 INTL 20030224)
ACPI: DMI detected: Acer
575MB HIGHMEM available.
896MB LOWMEM available.
mapped low ram: 0 - 38000000
low ram: 00000000 - 38000000
bootmap 00011000 - 00018000
(9 early reservations) ==> bootmem [0000000000 - 0038000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 00005c1520] TEXT DATA BSS ==> [0000100000 - 00005c1520]
#4 [003768e000 - 0037fef545] RAMDISK ==> [003768e000 - 0037fef545]
#5 [00005c2000 - 00005c5000] INIT_PG_TABLE ==> [00005c2000 - 00005c5000]
#6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f6950] 000f6950
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x00038000
HighMem 0x00038000 -> 0x0005bf70
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0005bf70
On node 0 totalpages: 376575
free_area_init_node: node 0, pgdat c04fc200, node_mem_map c1000200
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 146161 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 1 CPUs, 0 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
PM: Registered nosave memory: 00000000000d0000 - 00000000000d8000
PM: Registered nosave memory: 00000000000d8000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at 70000000 (gap: 6c000000:92c00000)
PERCPU: Allocating 38684 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 1, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 373632
Kernel command line: root=/dev/sda2 nomce quiet splash vga=791
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: Unable to calibrate against PIT
TSC: using PMTIMER reference calibration
Detected 2666.717 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1478372k/1506752k available (2972k kernel code, 27148k reserved, 1184k d
ata, 292k init, 589248k highmem)
virtual kernel memory layout:
fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0516000 - 0xc055f000 ( 292 kB)
.data : 0xc03e7055 - 0xc050f160 (1184 kB)
.text : 0xc0100000 - 0xc03e7055 (2972 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay loop (skipped), value calculated using timer frequency.. 5335.
66 BogoMIPS (lpj=8889056)
Security Framework initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: Hyper-Threading is disabled
using mwait in idle threads.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... works.
CPU0: Intel(R) Celeron(R) CPU 2.66GHz stepping 04
Brought up 1 CPUs
Total of 1 processors activated (5335.66 BogoMIPS).
net_namespace: 792 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd768, last bus=2
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x6, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:00.0 reg 10 32bit mmio: [ea000000, ebffffff]
PCI: 0000:00:00.0 reg 14 32bit mmio: [e8000000, e8000fff]
PCI: 0000:00:13.0 reg 10 32bit mmio: [e8001000, e8001fff]
PCI: 0000:00:13.1 reg 10 32bit mmio: [e8002000, e8002fff]
PCI: 0000:00:13.2 reg 10 32bit mmio: [e8003000, e8003fff]
pci 0000:00:13.2: supports D1
pci 0000:00:13.2: supports D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
PCI: 0000:00:14.0 reg 10 io port: [8060, 806f]
PCI: 0000:00:14.0 reg 14 32bit mmio: [e8004000, e80043ff]
PCI: 0000:00:14.1 reg 10 io port: [1f0, 1f7]
PCI: 0000:00:14.1 reg 14 io port: [3f4, 3f7]
PCI: 0000:00:14.1 reg 18 io port: [170, 177]
PCI: 0000:00:14.1 reg 1c io port: [374, 377]
PCI: 0000:00:14.1 reg 20 io port: [8070, 807f]
PCI: 0000:00:14.5 reg 10 32bit mmio: [e8004400, e80044ff]
PCI: 0000:00:14.6 reg 10 32bit mmio: [e8004800, e80048ff]
PCI: 0000:01:05.0 reg 10 32bit mmio: [f0000000, f7ffffff]
PCI: 0000:01:05.0 reg 14 io port: [9000, 90ff]
PCI: 0000:01:05.0 reg 18 32bit mmio: [e8100000, e810ffff]
PCI: 0000:01:05.0 reg 30 32bit mmio: [0, 1ffff]
pci 0000:01:05.0: supports D1
pci 0000:01:05.0: supports D2
PCI: bridge 0000:00:01.0 io port: [9000, 9fff]
PCI: bridge 0000:00:01.0 32bit mmio: [e8100000, e81fffff]
PCI: bridge 0000:00:01.0 32bit mmio pref: [f0000000, f7ffffff]
PCI: 0000:02:02.0 reg 10 io port: [a400, a41f]
PCI: 0000:02:02.0 reg 14 32bit mmio: [e8200800, e820081f]
PCI: 0000:02:02.0 reg 18 32bit mmio: [e8200000, e82007ff]
pci 0000:02:02.0: supports D2
PCI: 0000:02:03.0 reg 10 io port: [a000, a0ff]
PCI: 0000:02:03.0 reg 14 32bit mmio: [e8200c00, e8200cff]
pci 0000:02:03.0: supports D1
pci 0000:02:03.0: supports D2
pci 0000:02:03.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:02:03.0: PME# disabled
PCI: 0000:02:04.0 reg 10 32bit mmio: [0, fff]
pci 0000:02:04.0: supports D1
pci 0000:02:04.0: supports D2
pci 0000:02:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:00:14.4: transparent bridge
PCI: bridge 0000:00:14.4 io port: [a000, afff]
PCI: bridge 0000:00:14.4 32bit mmio: [e8200000, e82fffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
ACPI: RTC can wake from S4
system 00:07: ioport range 0x1080-0x1080 has been reserved
system 00:07: ioport range 0x220-0x22f has been reserved
system 00:07: ioport range 0x40b-0x40b has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x4d6-0x4d6 has been reserved
system 00:07: ioport range 0x530-0x537 has been reserved
system 00:07: ioport range 0xc00-0xc01 has been reserved
system 00:07: ioport range 0xc14-0xc14 has been reserved
system 00:07: ioport range 0xc50-0xc52 has been reserved
system 00:07: ioport range 0xc6c-0xc6c has been reserved
system 00:07: ioport range 0xc6f-0xc6f has been reserved
system 00:07: ioport range 0xcd6-0xcd7 has been reserved
system 00:07: ioport range 0x8000-0x805f has been reserved
system 00:07: ioport range 0xf40-0xf47 has been reserved
system 00:07: ioport range 0x280-0x293 has been reserved
system 00:08: iomem range 0xe0000-0xfffff could not be reserved
system 00:08: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:08: iomem range 0xe8000000-0xe8000fff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x9000-0x9fff
pci 0000:00:01.0: MEM window: 0xe8100000-0xe81fffff
pci 0000:00:01.0: PREFETCH window: 0x000000f0000000-0x000000f7ffffff
pci 0000:02:04.0: CardBus bridge, secondary bus 0000:03
pci 0000:02:04.0: IO window: 0x00a800-0x00a8ff
pci 0000:02:04.0: IO window: 0x00ac00-0x00acff
pci 0000:02:04.0: PREFETCH window: 0x70000000-0x73ffffff
pci 0000:02:04.0: MEM window: 0x74000000-0x77ffffff
pci 0000:00:14.4: PCI bridge, secondary bus 0000:02
pci 0000:00:14.4: IO window: 0xa000-0xafff
pci 0000:00:14.4: MEM window: 0xe8200000-0xe82fffff
pci 0000:00:14.4: PREFETCH window: 0x00000070000000-0x00000073ffffff
pci 0000:02:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 01 index 0 io port: [9000, 9fff]
bus: 01 index 1 mmio: [e8100000, e81fffff]
bus: 01 index 2 mmio: [f0000000, f7ffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [a000, afff]
bus: 02 index 1 mmio: [e8200000, e82fffff]
bus: 02 index 2 mmio: [70000000, 73ffffff]
bus: 02 index 3 io port: [0, ffff]
bus: 02 index 4 mmio: [0, ffffffff]
bus: 03 index 0 io port: [a800, a8ff]
bus: 03 index 1 io port: [ac00, acff]
bus: 03 index 2 mmio: [70000000, 73ffffff]
bus: 03 index 3 mmio: [74000000, 77ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 9605k freed
ACPI: EC: missing confirmations, switch off interrupt mode.
audit: initializing netlink socket (disabled)
type=2000 audit(1264678382.013:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/W].
msgmni has been set to 1756
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:05.0: Boot video device
vesafb: framebuffer at 0xf0000000, mapped to 0xf8880000, using 3072k, total 6553
6k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:52c8
vesafb: pmi: set display start = c00c5336, set palette = c00c5370
vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.103
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial 0000:00:14.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
serial 0000:00:14.6: PCI INT B disabled
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8070 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8078 irq 15
ata1.00: ATA-6: TOSHIBA MK4025GAS, KA100A, max UDMA/100
ata1.00: 78140160 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: PIONEER DVD-RW DVR-K14RA, 1.00, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4025GA KA10 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-K14RA 1.00 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 47x/47x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ehci_hcd 0000:00:13.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xe8003000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-1-mepis-smp ehci_hcd
usb usb1: SerialNumber: 0000:00:13.2
Initializing USB Mass Storage driver...
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: New USB device found, idVendor=046d, idProduct=09a5
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=2
usb 1-2: SerialNumber: A7194B60
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver appletouch
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 292k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/inpu
t1
ACPI: CPU0 (power states: C1[C1] C2[C2])
processor ACPI0007:00: registered as cooling_device0
agpgart-ati 0000:00:00.0: Ati IGP9100/M chipset
agpgart-ati 0000:00:00.0: AGP aperture is 32M @ 0xea000000
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 19, io mem 0xe8001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-1-mepis-smp ohci_hcd
usb usb2: SerialNumber: 0000:00:13.0
ohci_hcd 0000:00:13.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xe8002000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
8139too Fast Ethernet driver 0.9.28
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-1-mepis-smp ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
8139too 0000:02:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xa000, 00:02:3f:0e:19:ec, IRQ 19
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=1241, idProduct=1503
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB Keyboard
usb 2-1: Manufacturer:
usb 3-1: new low speed USB device using ohci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=046d, idProduct=c501
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: USB Receiver
usb 3-1: Manufacturer: Logitech
usbcore: registered new interface driver hiddev
input: USB Keyboard as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.0/input
/input2
input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:13.0-1
input: USB Keyboard as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.1/input
/input3
input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:13.0-1
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.1/usb3/3-1/3-1:1.
0/input/input4
input,hidraw2: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Marking TSC unstable due to TSC halts in idle
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 3973.200 MB/sec
xor: using function: pIII_sse (3973.200 MB/sec)
async_tx: api initialized (async)
raid6: int32x1 700 MB/s
raid6: int32x2 723 MB/s
raid6: int32x4 517 MB/s
raid6: int32x8 468 MB/s
raid6: mmxx1 1626 MB/s
raid6: mmxx2 1838 MB/s
raid6: sse1x1 942 MB/s
raid6: sse1x2 1819 MB/s
raid6: sse2x1 1923 MB/s
raid6: sse2x2 2833 MB/s
raid6: using algorithm sse2x2 (2833 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 125 started
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input6
ACPI: Lid Switch [LID]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/inpu
t7
ACPI: Power Button (CM) [PWRB]
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery absent)
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/device:1
3/input/input8
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8060, revision 0
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device (046d:09a5)
input: UVC Camera (046d:09a5) as /devices/pci0000:00/0000:00:13.2/usb1/1-2/1-2:1
.0/input/input9
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
Yenta: CardBus bridge found at 0000:02:04.0 [1025:0065]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x00111c12, devctl 0x44
Yenta: ISA IRQ mask 0x0ed8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
pcmcia: parent PCI bridge Memory window: 0x70000000 - 0x73ffffff
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
ATI IXP AC97 controller 0000:00:14.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ALSA atiixp.c:526: atiixp: codec reset timeout
ACPI: WMI: Mapper loaded
acer-wmi: Acer Laptop ACPI-WMI Extras
acer-wmi: No or unsupported WMI interface, unable to load
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x126eb1, caps: 0xa04713/0x4000
ATI IXP MC97 controller 0000:00:14.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input1
0
ALSA usbaudio.c:1319: 3:3:1: cannot get freq at ep 0x86
usbcore: registered new interface driver snd-usb-audio
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 104412k swap on /dev/sda3. Priority:1 extents:1 across:104412k
EXT3 FS on sda2, internal journal
ndiswrapper version 1.53 loaded (smp=yes, preempt=yes)
ndiswrapper: driver wlipnds () loaded
ndiswrapper 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ndiswrapper: using IRQ 18
wlan0: ethernet device 00:0e:9b:89:60:04 using NDIS driver: wlipnds, version: 0x
10016, NDIS version: 0x501, vendor: 'INPROCOMM IPN2220 Wireless LAN Adapter', 17
FE:2220.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
usbcore: registered new interface driver ndiswrapper
fuse init (API version 7.9)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
[drm] Initialized drm 1.1.0 20060810
pci 0000:01:05.0: power state changed by ACPI to D0
pci 0000:01:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.29.0 20080528 on minor 0
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ndiswrapper (set_essid:59): setting essid failed (00010003)
ndiswrapper (set_essid:59): setting essid failed (00010003)
agpgart-ati 0000:00:00.0: AGP 3.0 bridge
agpgart-ati 0000:00:00.0: putting AGP V3 device into 8x mode
pci 0000:01:05.0: putting AGP V3 device into 8x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
eth0: no IPv6 routers present
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 ' to make it known.
process `skype' is using obsolete setsockopt SO_BSDCOMPAT

Salut
Je viens d'essayer:
Mon correspondant reçoit ma voix déformée (ralentie) comme pour echo123.
De mon côté je reçois correctement sa voix.
Une précision, quand j'utilise echo123, j'entends correctement les messages de "l'opératrice", seul l'enregistrement de ma voix est déformé.

pas glop la bête !!!

j'ai essayé de désinstaller et de réinstaller la version 2.1.0.8.1 , c'est le même problème.

J'ai installer la version 2.0.0.7.2 et là çà marche très bien!

Ma machine est sûrement un peu juste.

Mais je peux communiquer et c'est le principal.

Merci beaucoup de ton aide

Cordialement

dh